hottub5

Patio Doors Repair – How to Fix a Wet Dog and Save Your Dog From Cold, Wet Feet Patio doors create a convenient and comfortable transition between your indoor and outdoor space. By keeping the air inside your home, they will save you money on heating or cooling bills. But over time, your sliding glass or French doors may lose their appeal. Simple repairs can keep your sliding glass or French doors looking and functioning like new. Weatherstripping You're walking your dog to the park at 5 am when you get into a puddle that is right next to your sliding patio door. You glance around and realize that the rain of last night blew in through the patio door seals. Be prepared, this isn't going to be a simple task in five minutes. But with a little patience and a few tools, you can fix this and keep your dog safe from wet, cold feet in the process. The most important thing is to replace the weatherstripping which closes the gap between the door and jamb, which prevents drafts, pests and moisture. It also keeps your energy bills down. A quick inspection of your windows and doors will let you know whether the weatherstripping in good condition or requires replacement. There are many types of weatherstripping that you can choose from that include open-cell and felt foam, vinyl and thermoplastic rubber, and metals like copper or bronze. Each type has its advantages and drawbacks. Foam and open-cell foam are both inexpensive however they tend to be noticeable and ineffective at blocking airflow. Vinyl is more expensive, however, it is durable and is resistant to moisture. Rubber is a good option for areas that have high traffic because it will not wear out as fast. To install new weatherstripping you must first remove the patio doors from the frame using a screwdriver to loosen the roller adjustment screws. Then, with a flathead screwdriver, loosen the plugs that secure the weatherstripping at the bottom of frame. Remove the weatherstripping that was previously installed from the frame and remove any adhesive remnants. Then, cut the replacement to the correct length, then peel back the plastic strip at one side and then apply it to the jamb using a putty knife. Reinstall the door and adjust the roller screws to ensure it is properly seated in the track. Apply waterproof caulk wherever the stationary panel is positioned to block sliding door and where the edge of the panel joins the frame. This is not a more secure seal than weatherstripping, but it should last for a while. Handles and locks Patio door handles and locks are essential to the security of your home. Over time, they can get damaged or worn out and require replacement. The spindle that connects the inside handles and the exterior handles may also be replaced. To replace a patio door handle first remove the previous one by unscrewing the screws that hold it in place. Once the old handle has been removed, use a level to ensure that the door is straight prior to installing the new handle. If the door isn't straight it can interfere with the lock. This could cause issues in the future. Once you have the new handle installed Close and then open it several times to ensure it functions properly. If you encounter any issues, check the manufacturer's instructions or a hardware expert for assistance. To avoid future issues, it is a good idea to also lubricate your lock mechanism with silicone-based lubricant. The most commonly used door lock for patio doors is the mortise latch. It's usually made of steel and fits inside a pocket carved into the door frame. These kinds of locks are found on wood and aluminum sliding doors. When replacing a mortise lock, it's important to measure a few things before purchasing a new lock. The measurements you need include the location of the mounting holes and the location of the keyway in the lock. Some patio door handles have an integrated locking mechanism that's integrated into the handle. These handles come with an elongated key cylinder that fits into the handle's keyway. This type of patio door has both the inside and exterior locks in one unit. This kind of patio door is often found on sliding aluminum doors. If the latch on your patio door isn't able to stay closed it could be because the lock tongue may not be catching the hasp correctly. Another possibility is that the sliding door is not completely parallel to the jamb's side. Try opening the door up to an inch and spotting it against the frame to determine whether there is any gap between the door and the jamb. If there is a gap, adjust the rollers to the bottom left or right side of the patio until it is exactly parallel to the jamb. Misalignment Over time, the door's tracks and rollers will lose their proper alignment. This could cause the doors to become stuck or difficult to move. patio door upkeep could also allow cold air and draughts to infiltrate your home, which could reduce the efficiency of your home's energy usage. It is possible to correct the misalignment and prevented. Applying a silicone-based lubricant to the tracks and rollers will help your doors move smoothly again. It's a good idea apply this every so often to ensure that your doors are in good working order. Another common problem with patio doors is a damaged screen, which can be a nuisance or even a security risk. It could also stop the doors from closing and opening correctly, which can result in energy loss. In some cases, the screen can be repaired but in other cases the door must be replaced. If you're experiencing a ripped screen, clean it thoroughly and make sure not to turn the handles of the door in the wrong way when opening and closing. Over time, hinges can loosen due to wear and tear or use. This can be corrected by tightening screws frequently. It's a simple job you can perform yourself. However, if you are not comfortable with the task, you should seek out an expert. It is also recommended to clean the rollers and tracks of your patio doors frequently. Simple brushing or vacuuming will get rid of dust and debris that could interfere with the smooth operation your patio doors. You can use a special tool for the most stubborn dirt or rust. The inspection and tightening of the hinges' screws can help with misalignment however, sometimes it's necessary to replace them altogether to ensure a secure, solid seal. The performance and alignment of your patio doors could be affected if the frames are warped or sliding. The warping or shifting may occur due to changes in the foundation of your home, but can also be caused by poor installation or simply due to frequent use. A professional can repair or replace your patio door frame and make sure it is properly aligned. This will allow it to function at its best. Rollers Sliding patio doors are great to let the outside in and providing ample natural light, however they do require a bit of maintenance to keep them sliding smoothly. If you need to pull the handle to get the door to move or it doesn't move as smoothly as it did in the past, it could be the rollers. Over time, the lower track can be clogged with dirt, dust, and mud. This makes it difficult for rollers to move. It is possible to clean it by spraying it with a lubricant like 2Slick. If the tracks have been cleaned but the rollers are still not moving freely, then it's time to replace them. Replacement rollers are available for your door and track type. They can be found at most hardware stores, but you'll require a companion to help with the removal and installation of the rollers. Take a photo of the roller assembly installed in the frame to assist the experts determine the exact model and type you require. They can also search for identifying characteristics such as bumps, dimples and cut-outs and flared edges that could narrow your the options for replacement. After replacing the rollers you will need to reinstall the sliding door back into its frame. This is a heavy door, and you might require assistance. Start by examining to make sure there aren't any screws securing the track in place on either side of the frame. Also, make sure that they are loose enough to allow the door's bottom to slide down into the channel on top of the frame. Remove the screen door from the opening. Make sure it's free of track tracks, rollers and track. After the new rollers have been installed, carefully insert the door into the frame, then swing it into place. If the new rollers are adjustable, you can adjust them to give the door a clearance in the areas it requires it.